The Foundation of Plumbing Knowledge for Bathtub Installation
The Foundation of Plumbing Knowledge for Bathtub Installation
Blog Article
We've uncovered this post pertaining to How to Install a Bathtub Yourself down the page on the net and believe it made perfect sense to talk about it with you on my blog.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a moderately challenging job. If the old bathtub is conveniently available, the task can move immediately; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the new one. Ensure you have qualified on your own for the task and also fit attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Opportunities are you may need a professional plumber to make tube connections.
This post will certainly aid you set up a new tub in your shower room if you have currently purchased a new bathtub as well as do not require to change the plan of your previous water pipes.
Your tools as well as material checklist ought to make up the following:
Planning for the Installment
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to avoid stress on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the restricted accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipelines have been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the tub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bath tub until the level reviews degree.
To set up taps, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply and also check all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bathtub as well as likewise examine the overflow outlet as well as the normal outlet for leaks.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bathtub must wait up until the bath tub has actually been made use of at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in place in between the tap and also the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type should be linked to the tap ends first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealant can fracture relatively very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that piece of content was a good thing. Be sure to take a moment to promote this article if you enjoyed it. Thank you so much for your time spent reading it.
Plumbing integrity assured. Report this page